Husqvarna FE 350 2014 Repair Manual Download Page 99

Page: 99 / 279

WHEELS

Remove engine sprocket

C,.

Remove screw connections (D. Remove the rear sprocket.
Position the new rear sprocket. Mount and tighten fittings.
Guideline

Nut, rear sprocket screw

35 Nm

(25.8 lbf ft)

Slide the new engine sprocket

onto the countershaft.

Mount the new chain.

Connect the chain with connecting link

C,.

Have an assistant operate the rear brake.
Mount and tighten screw

with the washer.

Guideline

Screw, engine sprocket

M10

Position the engine sprocket cover.
Mount and tighten screw

Guideline

Screw, clutch slave cylinder

Mount and tighten screw

Guideline

Remaining screws, chassis

Finishing work

Install the rear wheel. (.- p. 91)

60 Nm

(44.3 lbf ft)

Remove the motorcycle from the lift stand.(.- p. 11)

Loctite

2701

Loctite

2701

10 Nm (7.4 lbf ft)

25 Nm (18.4 lbf ft)

Summary of Contents for FE 350 2014
























































































































































































































































































Search results

Summary of Contents for FE 350 2014

Reviews:

Husqvarna FE 350 2014, Repair Manual, Page: 99 / 279

Search results

Summary of Contents for FE 350 2014

Reviews: