manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 98 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 98

14 

A 

WHEELS 

96 

Warning 

Danger of accidents 

Reduced braking efficiency due to oil or grease on the brake discs. 

- Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

Warning 

Environmental hazard 

Hazardous substances cause environmental damage. 

-

Oil,  grease,  filters,  fuel,  cleaners, brake fluid,  etc.,  should be disposed of as stipulated in applicable regulations.

Info 

The service life of the chain depends largely on its maintenance. 

Preparatory work 

Raise the motorcycle with a lift stand.(,....  p. 11) 

Main work 

Clean the chain regularly and then treat with chain spray. 

I 

Offroad chain spray (,....  p. 257)

400725-01 

Finishing work 

Remove the motorcycle from the lift stand.(,....  p. 11) 

14.6.10  Changing the drivetrain  kit 

Preparatory work 

Raise the motorcycle with a lift stand.(,....  p. 11) 

Remove the rear wheel. (,....  p. 90) 

Main work 

Remove screws 

O 

and 

8. 

Remove the engine sprocket cover. 

Have an assistant operate the rear brake. 
Remove screw 

@) 

with the washer.

Remove connecting link 

C, 

of the chain.

• 

Info

I 

Cover the components to protect them against damage. 

Take off the chain. 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments