manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 97 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 97

14 

WHEELS 

-

Check the chain sliding piece for wear.

If the lower edge of the chain pins is in line with or below the chain sliding 

piece: 
-

Change the chain sliding piece.

-

Check that the chain sliding piece is firmly seated.

If the chain sliding piece is loose: 

-

Tighten the chain sliding piece.

Guideline

Screw,  chain sliding piece 

-

Check the chain guide for wear.

•

Info

M8 

I 

Wear can be seen on the front of the chain guide. 

If the light part of the chain guide is worn: 

-

Change the chain guide.

-

Check that the chain guide is firmly seated.

If the chain guide is loose: 

-

Tighten the chain guide.

Guideline

Remaining screws,  chassis 

Remaining nuts,  chassis 

Finishing work 

M6 

M6 

-

Remove the motorcycle from the lift stand. (- p. 11)

14.6.8 

Checking for chain dirt accumulation 

400678-01 

14.6.9 

Cleaning the chain 

Warning 

-

Check the chain for coarse dirt accumulation.

If the chain is very dirty: 

-

Clean the chain. (- p. 95)

Danger of accidents 

Oil or grease on the tires reduces their grip. 

-

Remove oil and grease with a suitable cleaning material.

15  Nm 

(11 .1 lbf ft) 

10  Nm 

(7.4 lbf ft) 
10  Nm 

(7.4 lbf ft) 

95 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments