Husqvarna FE 350 2014 Repair Manual Download Page 94

Page: 94 / 279

14.6.3

14.6.4

WHEELS

- Position chain adjuster @). Mount nut

but do not tighten it yet.

- Make sure that chain adjusters @) are fitted correctly on adjusting screws

- Check the chain tension. (,... p. 93)

- Tighten nut

Guideline

Nut, rear wheel spindle

•

Info

M20x1.5

I 80 Nm (59 lbf ft)

The wide adjustment range of the chain adjusters (32 mm (1 .26 in))

enables different secondary ratios with the same chain length.

Chain adjusters@) can be turned by 180

- Operate the foot brake lever repeatedly until the brake linings are in contact with

the brake disc and there is a pressure point.

Finishing work

- Remove the motorcycle from the lift stand.(,... p. 11)

Removing the rear brake disc

Installing the rear brake disc

Preparatory work

- Raise the motorcycle with a lift stand.(,... p. 11)

- Remove the rear wheel. (,... p. 90)

Main work

- Remove screws

Take off the brake disc.

Main work

- Clean the contact surface of the brake disc.

- Position the brake disc with the label facing outward. Mount and tighten

screws

Guideline

Screw, rear brake disc

Finishing work

- Install the rear wheel. (,... p. 91)

14 Nm

(10.3 lbf ft)

- Remove the motorcycle from the lift stand.(,... p. 11)

Loctite

243

™

Summary of Contents for FE 350 2014
























































































































































































































































































Search results

Summary of Contents for FE 350 2014

Reviews:

Husqvarna FE 350 2014, Repair Manual, Page: 94 / 279

Search results

Summary of Contents for FE 350 2014

Reviews: