manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 87 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 87

13 

13.3 

MASK,  FENDER 

Removin  the headlight mask with the headlight 

Preparatory work 

-

Switch off all power consumers and switch off the engine.

Main work 

-

Open rubber bands 

O 

on the fork legs.

-

Tilt the headlight mask forward and detach at catch 

8.

-

Disconnect connector 

@).

-

Take off the headlight mask with headlight.

Main work 

-

Plug in connector 

O.

-

Check that the lighting is functioning properly.

-

Attach headlight holder 

8 

at catch 

@) 

and position the headlight mask.

-

Position rubber bands 

C, 

around the fork legs and close them.

✓ The wiring harness and brake line 

0 

are routed in front of the headlight

mask.

Finishing work 

-

Check the headlight setting.  (or  p. 118)

85 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments