manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 85 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 85

12 

FUEL TANK, SEAT, TRIM 

- Thoroughly clean the plug-in connection of the fuel line using compressed air.

•

Info

83 

I 

Under no circumstances should dirt enter into the fuel line. Dirt in the fuel 

line clogs the injection valve. 

- Press on the small metal plate and disconnect fuel hose connection 

O.

•

Info

I 

Remaining fuel may flow out of the fuel hose. 

- Mount special tool @.

I 

Pressure tester (61029094000) (

"" 

p. 262)

- Mount special tool 

(D 

with nozzle label 0,60.

I 

Testing hose (61029093000) (

"" 

p. 262)

- Position the hose end in a fuel cannister.

Guideline

I 

Minimum size of fuel cannister 

- Connect the diagnostics tool and start it.

110 I (2.6 US gal) 

- Select the 

"Function test of fuel pump control" 

actuator test.

Guideline

I 

Maximum duration of the actuator test 

I 

3 min

- Check the fuel pressure with the filler cap closed.

Fuel pressure

When the fuel pump is active 

If the specification is not reached: 

- Open the filler cap. (

"" 

p. 75)

- Check the tank air vent system.

3.35 ... 3.65 bar (48.6 ... 52.9 psi) 

- Check the fuel pressure with the filler cap open.

Fuel pressure

When the fuel pump is active 

If the specification is not reached: 

- Check that the fuel line is clear.

- Change the fuel filter. (

"" 

p. 79)

- Change the fuel pump.(

"" 

p. 81)

3.35 ... 3.65 bar (48.6 ... 52.9 psi) 

- Stop the 

"Function test of fuel pump control" 

actuator test by pressing the

"Quit" 

button.

- Remove the special tools.

- Join the fuel hose connection.

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments