manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 84 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 84

12 

FUEL TANK, SEAT, TRIM 

305313-10 

305314-10 

Main work 

- Remove nut 

O 

with the gasket.

- Remove fuel connection 

8 

with the gasket.

- Remove screws 

8.

- Pull out the fuel pump.

- Position the fuel pump.

- Mount fuel connection @ with the gasket but do not tighten yet.

Guideline

I 

Fuel connection on fuel pump 

I 

M8 

- Mount and tighten nut 

O 

with the gasket.

Guideline

10  Nm (7.4 lbf ft) 

82 

I 

Nut, fuel pump fixation 

15 Nm (11.1 lbf ft) 

305313-10 

305314-10 

Tighten fuel connection 

@.

Guideline 

I 

Fuel connection on fuel pump 

- Mount and tighten screws 

8.

Guideline

I 

Screw, fuel pump 

10  Nm (7.4 lbf ft) 

I 

EJOT PT

® 

I  3  Nm (2.2 lbf ft) 

12.12  Checking the fuel  �ressure 

m 

A 

Danger 
Fire hazard 

Fuel is highly flammable. 

- Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no

fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

- The fuel in the fuel tank expands when warm and may emerge if overfilled. Follow the instructions on refueling.

Warning 

Danger of poisoning 

Fuel is poisonous and a health hazard. 

- Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with

the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with

soap and water. If fuel is swallowed, contact a physician immediately. Change clothing that has been contaminated with

fuel. Store fuel properly in a suitable canister and keep away from children.

Condition 

The fuel tank is full. 

Ensure that the battery voltage does not drop below 12.5 V. 

The diagnostics tool is disconnected. 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments