Husqvarna FE 350 2014 Repair Manual Download Page 83

Page: 83 / 279

FUEL TANK, SEAT, TRIM

305316-10

305313-10

305314-10

- Mount fuel filter

✓ Arrow

points away from the fuel pump.

- Mount hose clamps

C,.

Hose clamp pliers (60029057000) (or p. 261)

- Position the fuel pump.

- Mount fuel connection @ with the gasket but do not tighten yet.

Guideline

Fuel connection on fuel pump

- Mount and tighten nut

with the gasket.

Guideline

Nut, fuel pump fixation

- Tighten fuel connection@.

Guideline

Fuel connection on fuel pump

- Mount and tighten screws

@).

Guideline

Screw, fuel pump

Finishing work

- Install the fuel tank. (or p. 78)

- Mount the seat. (or p. 76)

EJOT PT

10 Nm (7.4 lbf ft)

115 Nm (11.1 lbf ft)

10 Nm (7.4 lbf ft)

I 3 Nm (2.2 lbf ft}

12.11

Changing the fuel

Danger
Fire hazard

Fuel is highly flammable.

- Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no

fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

- The fuel in the fuel tank expands when warm and may emerge if overfilled. Follow the instructions on refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

- Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with

the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with

soap and water. If fuel is swallowed, contact a physician immediately. Change clothing that has been contaminated with

fuel. Store fuel properly in a suitable canister and keep away from children.

Warning

Environmental hazard

Improper handling of fuel is a danger to the environment.

- Do not allow fuel to get into the ground water, the ground, or the sewage system.

Preparatory work

- Drain the fuel from the fuel tank into a suitable container.

- Remove the seat. (or p. 76)

- Remove the fuel tank. (or p. 76)

Summary of Contents for FE 350 2014
























































































































































































































































































Search results

Summary of Contents for FE 350 2014

Reviews:

Husqvarna FE 350 2014, Repair Manual, Page: 83 / 279

Search results

Summary of Contents for FE 350 2014

Reviews: