manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 79 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 79

12 

FUEL TANK, SEAT, TRIM 

Main work 

-

Unplug connector 

O 

of the fuel pump.

-

Pull the hose off the fuel tank breather on the tank lid.

-

Thoroughly clean the plug-in connection of the fuel line with an air line.

•

Info

I 

Dirt should not be allowed to get into the fuel line under any 

circumstances.  Dirt in the fuel line clogs the injection valve! 

-

Disconnect the plug-in connection of the fuel line.

•

Info

I 

Remaining fuel may run out of the fuel pipe. 

-

Mount wash cap set 

8.

I 

Wash cap set (81212016100)

(FE 350 EU/ AU) 

-

Disconnect the connector of the horn.

-

Remove screws 

8 

with the collar bushings and horn.

(FE 350 US) 

-

Remove screws 

8 

with the collar bushings.

-

Remove screw 

C, 

with the rubber bushing.

77 

-

Pull both spoilers off of the sides of the radiator bracket and lift off the fuel tank.

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments