manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 75 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 75

11 

AIR FILTER 

11.3 

Removin  the air filter 

Note 

73 

-

Release catch 

Q, 

pull off the air filter box lid sideways in areas  f) and  G), and

remove toward the rear.

-

Position the air filter box cover and catch 

O. 

Engage the air filter box cover in

areas  f) and  G).

-

Engage catch 

O.

Engine failure 

Unfiltered intake air has a negative effect on the service life of the engine. 

-

Never operate the vehicle without an air filter as dust and dirt will enter the engine and lead to increased wear.

Warning 

Environmental hazard 

Hazardous substances cause environmental damage. 

-

Oil,  grease,  filters,  fuel,  cleaners,  brake fluid,  etc.,  should be disposed of as stipulated in applicable regulations.

Preparatory work 

-

Remove the air filter box cover. (,r  p. 73)

Main work 

-

Push air filter holding bracket 

O 

toward the air filter at position  f),  and detach it

at end  G).

-

Swivel the air filter holding bracket to one side and remove the air filter with the

air filter support.

-

Take off air filter from air filter support.

Main work 

-

Mount the clean air filter on the air filter support.

-

Grease the air filter in area  f).

I 

Long-life grease (or  p. 257)

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments