manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 73 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 73

10  EXHAUST 

-

Install the right side cover. (

or 

p. 76)

-

Mount the seat.  (

or 

p. 76)

-

Remove the motorcycle from the lift stand. (

or 

p. 11)

Removin  the main silencer 

Warning 

Danger of burns 

The exhaust system gets very hot when the vehicle is driven. 

- Allow the exhaust system to cool down. Do not touch hot components.

lnstallin 

Preparatory work 

-

Remove the right side cover. (

or 

p. 75)

Main work 

-

Disconnect spring 

O.

I 

Spring hook  (50305017000)  (

or 

p. 259) 

-

Remove screws @ and take off the main silencer.

Main work 

-

Mount the main silencer.  Mount screws 

O 

but do not tighten yet.

Reconnect spring@.

I 

Spring hook (50305017000)  (

or 

p. 259)

-

Tighten screws 

O.

Guideline

I 

Remaining screws,  chassis

Finishing work 

-

Install the right side cover. (

or 

p. 76)

Changing the glass fiber �arn filling of the main silencer 

Warning 

Danger of burns 

The exhaust system gets very hot when the vehicle is driven. 

- Allow the exhaust system to cool down. Do not touch hot components.

Info 

Over time,  the fibers of the glass fiber yarn escape and the damper  "burns"  out. 

Not only is the noise level higher,  the performance characteristic changes. 

Preparatory work 

-

Remove the right side cover. (

or 

p. 75)

-

Remove the main silencer. (

or 

p. 71)

10 Nm (7.4 lbf ft) 

71 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments