manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 48 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 48

9 

SHOCK ABSORBER, SWINGARM 

Main work 

-

Carefully take the shock absorber out of the vehicle toward the top.

Main work 

-

Carefully position the shock absorber into the vehicle from above.

Finishing work 

-

Install the manifold.  (,r- p. 69)

-

Mount the seat.  (,r- p.  76)

-

Install the main silencer.  (,r- p.  71)

-

Install the right side cover.  (- p.  76)

-

Remove the motorcycle from the lift stand.  (- p. 11)

9.11 

Checkin  the shock absorber linka  e 

Preparatory work 

-

Raise the motorcycle with a lift stand.  (,r- p. 11)

Main work 

-

Remove screw 

O.

-

Remove fitting 

8.

Info 

Raise the wheel slightly to be able to remove the screws more easily. 

-

Remove fitting 

8.

-

Take off the angle lever.

46 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments