Husqvarna FE 350 2014 Repair Manual Download Page 36

Page: 36 / 279

6.28

FORK, TRIPLE CLAMP

Checkin the steerin head bearing la

Warning

Danger of accidents

Unstable vehicle handling from incorrect steering head bearing play.

- Adjust the steering head bearing play without delay.

Info

If the bike is ridden with play in the steering head bearing, the bearing and the bearing seats in the frame can become dam

aged over time.

Preparatory work

- Raise the motorcycle with a lift stand.(,... p. 11)

Main work

- Move the handlebar to the straight-ahead position. Move the fork legs to and fro

in the direction of travel.

No play should be noticeable in the steering head bearing.

If there is noticeable play present:

- Adjust the play of the steering head bearing. (,... p. 34)

- Move the handlebar to and fro over the entire steering range.

The handlebar must be able to move easily over the entire steering range. No

resting locations should be noticeable.

If click positions are noticeable:

- Adjust the play of the steering head bearing. (,... p. 34)

- Check the steering head bearing and replace if required.

Finishing work

- Remove the motorcycle from the lift stand.(,... p. 11)

Ad"usting the la of the steering head bearing

Preparatory work

- Raise the motorcycle with a lift stand.(,... p. 11)

Main work

- Loosen screws

Remove screw

- Loosen and retighten screw

Guideline

Screw, top steering head

M20x1 .5

112 Nm (8.9 lbf ft)

- Using a plastic hammer, tap lightly on the upper triple clamp to avoid strains.

- Tighten screws

Guideline

Screw, top triple clamp

- Mount and tighten screw

Guideline

Screw, top steering stem

Finishing work

17 Nm

(12.5 lbf ft)

- Check the steering head bearing play.(,... p. 35)

- Remove the motorcycle from the lift stand.(,... p. 11)

17 Nm (12.5 lbf ft)

Loctite

243

™

Summary of Contents for FE 350 2014
























































































































































































































































































Search results

Summary of Contents for FE 350 2014

Reviews:

Husqvarna FE 350 2014, Repair Manual, Page: 36 / 279

Search results

Summary of Contents for FE 350 2014

Reviews: