Husqvarna FE 350 2014 Repair Manual Download Page 27

Page: 27 / 279

FORK, TRIPLE CLAMP

--e

��'�

Assemblin

Info

201975-10

iston rod

- Mount shim stack @ with the smaller washers facing downward.

- Mount and tighten sleeve

@).

Guideline

Hydrostop unit sleeve

M6x0.5

- Check distance

and total length G) of the hydrostop.

Guideline

I 7 Nm (5.2 lbf ft)

Hydrostop distance

;;,: 1.5 mm (;;,: 0.059 in)

Hydrostop length

If the dimensions are out of tolerance:

- Add or remove washers

108.5 ... 109.5 mm (4.272 ... 4.311 in)

The steps are identical for both fork legs, except for the hydrostop needle and valve.

201730-10

- Degrease the piston rod.

- Clamp the piston rod with the special tool.

Clamping stand (T14049S) (

p. 269)

- Lubricate the O-ring. Mount valve needle

in the piston rod.

Lubricant (T158) (

p. 257)

- Mount spring

@}.

- Mount and tighten adapter

with spring

and washer.

Guideline

Adapter of piston rod

M6x0.5

- Position the spring.

12 Nm (8.9 lbf ft)

- Mount the compression shim stack

with the smaller washers facing down-

ward.

Summary of Contents for FE 350 2014
























































































































































































































































































Search results

Summary of Contents for FE 350 2014

Reviews:

Husqvarna FE 350 2014, Repair Manual, Page: 27 / 279

Search results

Summary of Contents for FE 350 2014

Reviews: