manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 196 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 196

21 

21.5 

LUBRICATION  SYSTEM 

194 

Adding engine oil 

Info 

Too little engine oil or poor-quality engine oil results in premature wear to the engine. 

Main work 

-

Remove the oil filler plug 

O 

with the O-ring from the clutch cover.

Fill engine oil to the middle 

f) 

of the level viewer.

I 

Engine oil (SAE 1 0W/50)  (

,... 

p. 256)

•

Info

I 

For optimal performance of the engine oil, do not mix different types of 

engine oil. 

If appropriate, change the engine oil. 

-

Install and tighten the oil filler plug with O-ring.

Danger 

Danger of poisoning 

Exhaust gases are toxic and inhaling them may 

result in unconsciousness and/or death. 

When running the engine, always make sure there is sufficient ventila­

tion, and do not start or run the engine in an enclosed space without 

an effective exhaust extraction system. 

-

Start the engine and check that it is oil-tight.

Finishing work 

-

Check the engine oil level. (

,... 

p. 191)

-

Check the engine oil level. (

,... 

p. 191)

-

Remove the release screw of the chain adjuster.

-

Mount and tighten special tool 

O.

Guideline

I 

Oil pressure adapter

I 

M10x1

I 

Oil pressure adapter (77329006000) (

,... 

p. 266)

10 Nm (7.4 lbf ft) 

-

Connect pressure tester 

8 

to the special tool without the T-plate.

I 

Pressure tester (61029094000) (

,... 

p. 262)

Danger 

Danger of poisoning 

Exhaust gases are toxic and inhaling them may 

result in unconsciousness and/or death. 
-

When running the engine, always make sure there is sufficient ventila­

tion, and do not start or run the engine in an enclosed space without

an effective exhaust extraction system.

-

Start the engine and let it warm up.

-

Check the engine oil pressure.

Engine oil pressure 

Engine oil temperature:  80 °C 

(176 °F) 
Engine speed:  1,600 rpm 

Engine oil temperature: 80 °c 

(176 °F) 
Engine speed:  6,000 rpm 

0.9 bar (13 psi) 

2.5 bar (36 psi) 

If the measured value is less than the specification: 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments