Husqvarna FE 350 2014 Repair Manual Download Page 195

Page: 195 / 279

LUBRICATION SYSTEM

- Remove screws

Take off the oil filter cover with the O-ring.

- Pull oil filter

out of the oil filter housing.

Circlip pliers reverse (51012011000) (- p. 260)

- Completely drain the engine oil.

- Thoroughly clean the parts and sealing area.

- Lay the motorcycle on its side and fill the oil filter housing to about ½ full with

engine oil.

- Fill the oil filter with engine oil and place it in the oil filter housing.

193

- Lubricate the O-ring of the oil filter cover and mount it with the oil filter cover (D.

- Mount and tighten the screws.

Guideline

Screw, oil filter cover

- Stand the motorcycle upright.

10 Nm (7.4 lbf ft)

- Remove the oil filler plug @ with the O-ring from the clutch cover and fill up with

engine oil.

Engine oil

11.20 I (1.27 qt.)

Engine oil (SAE 1 0W/50) (- p. 256)

•

Info

Too little engine oil or poor-quality engine oil results in premature wear to

the engine.

- Install and tighten the oil filler plug with O-ring.

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may

result in unconsciousness and/or death.

- When running the engine, always make sure there is sufficient ventila

tion, and do not start or run the engine in an enclosed space without

an effective exhaust extraction system.

- Start the engine and check that it is oil-tight.

Finishing work

- Check the engine oil level. (- p. 191)

- Install the engine guard. (- p. 41)

Summary of Contents for FE 350 2014
























































































































































































































































































Search results

Summary of Contents for FE 350 2014

Reviews:

Husqvarna FE 350 2014, Repair Manual, Page: 195 / 279

Search results

Summary of Contents for FE 350 2014

Reviews: