manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 194 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 194

21 

LUBRICATION  SYSTEM 

Changing the engine oil and oil filter, cleaning the oil screen 

Warning 

Danger of scalding 

Engine oil and gear oil get very hot when the motorcycle is ridden. 

- Wear appropriate protective clothing and safety gloves. In case of burns, rinse immediately with lukewarm water.

Warning 

Environmental hazard 

Hazardous substances cause environmental damage. 

- Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info 

Drain the engine oil only when the engine is warm. 

Preparatory work 

- Park the motorcycle on a level surface.

- Remove the engine guard.(,.... p. 41) 

Main work 

- Place a suitable container under the engine.

- Remove oil drain plug 

O 

with the magnet and seal ring.

Info 

Do not remove screws 

f) 

on both sides. 

- Remove screw plug 

8 

with oil screen  (D  and the O-rings.

Completely drain the engine oil.

- Thoroughly clean the parts and sealing surfaces.

- Position oil screen (D with the O-rings on a pin wrench.

192 

- Position the pin wrench through the drilled hole of the screw plug in the opposite

section of the engine case.

- Push the oil screen all the way into the engine case.

- Mount and tighten screw plug 

8 

with the O-ring.

Guideline

I 

Screw plug, oil screen 

I 

M20x1 .5 

115 Nm (11.1 lbf ft) 

I 

- Mount and tighten the oil drain plug 

O 

with the magnet and a new seal ring.

Guideline

I 

Oil drain plug with magnet 

I 

M12x1.5 

I 

20 Nm (14.8 lbf ft) 

I 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments