Husqvarna FE 350 2014 Repair Manual Download Page 19 | Manualshive

Page: 19 / 279

Husqvarna FE 350 2014 Repair Manual Download Page 19

6

6.11

,.

t

ii

FORK, TRIPLE CLAMP

Performing a fork service

0

Condition

The fork legs have been removed.

-

Disassemble the fork legs. (,... p. 17)

-

Remove the spring. (,... p. 19)

-

Disassemble the cartridge. (,... p. 20)

-

Disassemble the piston rod.(,... p. 21)
Disassemble the hydrostop unit. (,... p. 22)

-

Disassemble the seal ring retainer. (,... p. 22)

-

Check the fork legs. (,... p. 23)

- Assemble the seal ring retainer. (,... p. 24)
- Assemble the hydrostop unit. (,... p. 24)
- Assemble the piston rod. (,... p. 25)
- Assemble the cartridge. (,... p. 26)

17

• "'0

ll

e

- Assemble the fork legs. (,... p. 27)

'

�

i

go

$0

201926-01

Disassemblin the fork le s

Info

The steps are identical for both fork legs.

201700-10

201701-10

Condition

The fork legs are disassembled.

-

Note down the current state of rebound damping

O

REB

(red adjuster of right

fork leg).

-

Note down the current state of compression damping @

COMP

(white adjuster

of left fork leg).

Fully open the adjusters of the rebound and compression damping.

-

Clamp the fork leg in the area of the lower triple clamp.

I

Clamping stand (T1403S) (,... p. 268)

-

Remove the screw. Remove adjuster@).

-

Release screw cap

C,.

I

Special socket (T14047) (,... p. 269)

•

Info

I

The cartridge cannot be taken off yet.

«
...
17
18
19
20
21
...
»

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments