Husqvarna FE 350 2014 Repair Manual Download Page 185

Page: 185 / 279

18 ENGINE

183

18.5.26 Checking the valve clearance

- Remove screw

- Crank over the engine repeatedly.

- Position the engine at ignition top dead center.

✓ Markings

on the cylinder head are flush above the flat areas

of the

camshafts.

- Check the valve clearance at all valves between the camshaft and cam levers.

Guideline

Valve clearance

Intake at: 20 °c (68 °F)

0.10 ... 0.15 mm (0.0039 ... 0.0059 in)

Exhaust at: 20 °C (68 °F)

0.13 ... 0.18 mm (0.0051 ... 0.0071 in)

Feeler gauge (590290411 00) (r p. 261)

If the valve clearance does not meet specifications:

- Adjust the valve clearance. (r p. 183)

- Mount and tighten screw

with the washer.

18.5.27 Adjusting the valve clearance

Guideline

Screw plug, crankshaft location

Main work

- Remove the timing chain tensioner. (r p. 131)

- Remove the camshaft. (r p. 132)

- Raise cam levers

110 Nm (7.4 lbf ft)

- Correct the shims according to the findings from checking the valve clearance.

- Install the camshafts. (r p. 180)

- Install the timing chain tensioner. (r p. 182)

Finishing work

- Check the valve clearance. (r p. 183)

Summary of Contents for FE 350 2014
























































































































































































































































































Search results

Summary of Contents for FE 350 2014

Reviews:

Husqvarna FE 350 2014, Repair Manual, Page: 185 / 279

Search results

Summary of Contents for FE 350 2014

Reviews: