Husqvarna FE 350 2014 Repair Manual Download Page 181

Page: 181 / 279

18 ENGINE

18.5.21 Installing the cylinder head

Insert the special tool and press it forcefully to the piston.

179

Turn the special tool clockwise, thereby pushing the piston pin retainer into the

groove.

Insertion for piston ring lock (77229030000) (or- p. 264)

Ensure that the piston pin retainer is seated properly on both sides.

Remove the cloth.

Keep the timing chain taut. Push the cylinder down carefully and let the dowel

pins engage.

Position cylinder head gasket

•

Info

Ensure that the dowels are seated properly.

Put the cylinder head in place.

Mount nut

with the washers and tighten in a crisscross pattern.

Guideline

Nut, cylinder head

M10x1 .25

Tightening

Thread, oiled with

sequence:

engine oil/cone

Tighten diag-

greased

anally.

1st tightening

stage

10 Nm

(7.4 lbf ft)
2nd tighten-

ing stage
30 Nm

(22.1 lbf ft)

3rd tightening

stage

50 Nm

(36.9 lbf ft)

Summary of Contents for FE 350 2014
























































































































































































































































































Search results

Summary of Contents for FE 350 2014

Reviews:

Husqvarna FE 350 2014, Repair Manual, Page: 181 / 279

Search results

Summary of Contents for FE 350 2014

Reviews: