manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 18 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 18

6 

FORK, TRIPLE CLAMP 

- Position the brake caliper, and mount and tighten screws 

8.

Guideline

Screw, front brake caliper  MS 

- Mount the cable tie(s).

25 Nm 

(18.4 lbf ft) 

16 

Loctite

® 

243

™ 

- Position the brake line, wiring harness, and clamp. Mount and tighten screws 

0.

Finishing work 

- Install the front wheel. (,... p. 88)

- Install the headlight mask with the headlight. (,... p. 85)

- Check the headlight setting. (,... p. 118)

6.9 

Removing the fork protector 

6.10 

C00565-10 

Preparatory work 

- Switch off all power consumers and switch off the engine.

- Remove the headlight mask with the headlight. (,... p. 85)

- Raise the motorcycle with a lift stand.(,... p. 11)

- Remove the front wheel. (,... p. 88)

- Remove the fork legs. (,... p. 15)

Main work 

- Remove screws 

O 

on the left fork leg. Remove the fork protector upwards.

- Remove the screws on the right fork leg. Remove the fork protector upwards.

Installing the fork  rotector 

C00565-10 

Main work 

- Position the fork protector on the left fork leg. Mount and tighten screws 

O.

Guideline

I 

Remaining screws, chassis 

I10Nm(7.41bf ft) 

- Position the fork protector on the right fork leg. Mount and tighten the screws.

Guideline

I 

Remaining screws, chassis 

Finishing work 

- Install the fork legs. (,... p. 15)

- Install the front wheel. (,... p. 88)

- Install the headlight mask with the headlight. (,... p. 85)

- Check the headlight setting. (,... p. 118)

I 10Nm(7.41bf ft) 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments