manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 178 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 178

18  ENGINE 

Position the clutch cover. 

•

Info

176 

I 

Ensure that the shaft seal rings of the water pump and the crankshaft are 

not damaged. 

- Remove screw 

O.

- Mount screw @ with the washer but do not tighten yet.

Guideline

I 

Screw, clutch cover 

I 

M6x25 

- Mount screws 

(D 

but do not tighten yet.

Guideline

I 

Screw, clutch cover 

I 

M6x40 

- Tighten all screws in a crisscross pattern.

110 Nm (7.4 lbf ft) 

110 Nm (7.4 lbf ft) 

18.5.18  Installing the water pump cover 

18.5.19  Installing the starter drive 

- Mount the two-part water pump impeller 

O.

- Mount and tighten nut@.

Guideline

Nut, water-pump wheel 

M6 

5Nm 

(3.7 lbf ft) 

- Mount the water pump cover with the seal ring.

•

Info

I 

Ensure that the dowel pins are seated properly. 

- Mount screw 

(D 

but do not tighten yet.

Guideline

I 

Screw, water pump cover

I 

M6x25 

- Mount screws 

8 

but do not tighten them yet.

Guideline

I 

Screw, water pump cover 

I 

M6x40 

- Mount screw 

0 

with the washer but to not tighten yet.

Guideline

I 

Screw, water pump cover 

I 

M6x25 

- Tighten all screws in a crisscross pattern.

- Grease the O-ring of the starter motor.

- Position the starter motor.

- Mount screws 

0, 

but do not tighten yet.

Guideline

I 

Screw, starter motor 

Loctite

® 

243

™ 

110 Nm (7.4 lbf ft) 

10 Nm (7.4 lbf ft) 

10 Nm (7.4 lbf ft) 

10 Nm (7.4 lbf ft) 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments