manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 139 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 139

18  ENGINE 

18.3.20  Removing the clutch basket 

18.3.21  Removing the shift shaft 

-

Completely remove clutch disc pack  (D.

-

Remove clutch pressure piece 

@.

-

Bend open lock washer.

-

Hold the inner clutch hub with the special tool.  Loosen nut 

O.

I 

Clutch holder (51129003000)  (- p. 260)

-

Remove the nut with the lock washer.  Dispose of the lock washer.

-

Take off inner clutch hub 

8 

and washer 

CD.

•

Info

I 

The washer usually sticks to the inner clutch hub. 

-

Take off clutch basket 

8.

-

Take off needle bearing 

0 

and collar sleeve  (D.

-

Push sliding plate 

O 

away from the shift drum locating unit 

8. 

Remove shift

shaft 

CD 

with the washer.

137 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments