manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 113 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 113

16 

BRAKE SYSTEM 

111 

-

Check that leaf spring 

0 

in the brake caliper and sliding plate 

(D 

in the brake

caliper support are seated properly.

✓ The arrow on the leaf spring points in the rotation direction of the brake disc.

-

Insert the new brake linings,  insert pin 

8, 

and mount cotter pins  (D.

•

Info

I 

Always change the brake linings in pairs. 

Make sure that decoupling plate  @  is mounted on the piston side of the 

brake lining. 

- Operate the foot brake lever repeatedly until the brake linings are in contact with

the brake disc and there is a pressure point.

- Add brake fluid to level  f).

I 

Brake fluid DOT 4  (.- p. 256)

-

Mount screw cap 

O 

with membrane 

8 

and O-ring.

Info 

Clean up overflowed or spilt brake fluid immediately with water. 

Checkin  the free travel of foot brake lever 

Warning 

Danger of accidents 

Brake system failure. 

-

If there is no free travel on the foot brake lever,  pressure builds up on the rear brake circuit. The rear brake can fail due to

overheating. Adjust the free travel on foot brake lever according to specifications.

402026-10 

-

Disconnect spring 

O.

-

Move the foot brake lever back and forth between the end stop and the contact

to the foot brake cylinder piston and check free travel  f).

Guideline

I 

Free travel at foot brake lever

13 ... 

5 mm (0.12 ...  0.2 in)

If the free travel does not meet specifications: 

- Adjust the basic position of the foot brake lever. (.- p. 112)

-

Reconnect spring 

O.

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments