manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 112 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 112

16 

A 

A 

A 

A 

BRAKE SYSTEM 

Changing the rear brake linin  s 

Warning 

Danger of accident 

Brake system failure. 

Maintenance work and repairs must be carried out professionally. 

Warning 
Skin irritation 

Brake fluid can cause skin irritation on contact. 

- Avoid contact with skin and eyes, and keep out of the reach of children.

- Wear suitable protective clothing and goggles.

110 

If brake fluid comes into contact with the eyes,  flush the eyes thoroughly with water and consult a physician immediately.

Warning 

Danger of accidents 

Reduced braking efficiency due to old brake fluid. 

-

Change the brake fluid of the front and rear brake according to the service schedule.

Warning 

Danger of accidents 

Reduced braking efficiency due to oil or grease on the brake discs. 

- Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

Warning 

Danger of accident 

Reduced braking efficiency due to the use of non-approved brake linings. 

Brake linings available in accessories stores often have not been tested and approved for use in Husqvarna motorcy­

cles. The structure and friction coefficient of the brake linings and thus their brake power may vary greatly from that of 

original Husqvarna Motorcycles bake linings. If brake linings that differ from the original equipment are used,  it cannot 

be guaranteed that these are in keeping with the original homologation.  In this case,  the vehicle will not correspond to its 

condition at delivery and the warranty shall be void. 

Warning 

Environmental  hazard 

Hazardous substances cause environmental damage. 

-

Oil,  grease,  filters,  fuel,  cleaners,  brake fluid,  etc.,  should be disposed of as stipulated in applicable regulations.

Info 

Never use DOT 5 brake fluid. It is silicone-based and purple in color. Oil seals and brake lines are not designed for  DOT 5 

brake fluid. 
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint! 

Use only clean brake fluid from a sealed container. 

Stand the vehicle upright. 

Remove screw cap 

O 

with membrane  @  and the O-ring. 

Press the brake caliper onto the brake disc by hand in order to push back the 

brake piston and ensure that brake fluid does not flow out of the brake fluid reser­

voir,  extracting it by suction if it does. 

• 

Info

I 

Ensure that the brake caliper is not pressed against the spokes when 

pushing back the brake piston. 

Remove cotter pin 

CD, 

pull out pine  and remove the brake linings. 

Clean the brake caliper and brake caliper support. 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments