Husqvarna FE 350 2014 Repair Manual Download Page 111

Page: 111 / 279

BRAKE SYSTEM

>------400379-10

Open shut-off valve

•

Info

Follow the operating instructions of the bleeding device.

Ensure that the filling pressure is correctly set at pressure gauge 6). If neces

sary, adjust the filling pressure at pressure regulator

G).

Guideline

Filling pressure

2 ... 2.5 bar (29 ... 36 psi)

109

Pull off protection cap

of the brake caliper bleeder screw. Connect the hose

of the bleeder bottle.

Bleeding device (00029013100) (- p. 259)

Open bleeder screw

by approx. one-half turn.

•

Info

Bleed until fresh brake fluid emerges from the bleeder bottle hose without

bubbles.

Tighten the bleeder screw.

Close shut-off valve

Open the bleeder screw again until no more brake fluid emerges.

•

Info

This prevents overfilling of the brake fluid reservoir.

Tighten the bleeder screw. Remove the hose of the bleeder bottle. Mount the pro

tection cap.

Disconnect the bleeding device. Remove the bleeder cover.

- Add brake fluid to level (D.

Guideline

Measurement of (D

Brake fluid DOT 4 (- p. 256)

5 mm (0.2 in)

Position the cover with the membrane. Mount and tighten the screws.

•

Info

Clean up overflowed or spilt brake fluid immediately with water.

Check the hand brake lever for a firm pressure point.

Checking the rear brake linings

Warning

Danger of accidents

Reduced braking efficiency caused by worn brake linings.

Change worn brake linings immediately.

Check the brake linings for minimum thickness 6).

Minimum thickness 6)

I �

1 mm (� 0.04 in)

If the minimum thickness is less than specified:

Change the rear brake linings. (- p. 110)

Check the brake linings for damage and cracking.

If damage or cracking is visible:

Change the rear brake linings. (- p. 110)

Summary of Contents for FE 350 2014
























































































































































































































































































Search results

Summary of Contents for FE 350 2014

Reviews:

Husqvarna FE 350 2014, Repair Manual, Page: 111 / 279

Search results

Summary of Contents for FE 350 2014

Reviews: