manualshive.com logo in svg

Husqvarna FE 350 2014, Repair Manual, Page: 104 / 279

Share
Download
Husqvarna FE 350 2014 Repair Manual Download Page 104

15 

WIRING  HARNESS,  BATTERY 

Removin  the batte 

Warning 

Risk of injury 

Battery acid and battery gases cause serious chemical burns. 

-

Keep batteries out of the reach of children.

-

Wear suitable protective clothing and goggles.

- Avoid contact with battery acid and battery gases.
-

Keep sparks and open flames away from the battery. Only charge in well-ventilated rooms.

-

In the event of skin contact,  rinse with large amounts of water. If battery acid gets in the eyes,  rinse with water for at 

least 15 minutes and contact a physician.

Preparatory work 

-

Switch off all power consumers and switch off the engine.

-

Remove the seat. (

.-

p. 76)

Main work 

102 

-

Pull back the negative terminal cover 

O 

and disconnect the negative cable from

the battery.

-

Pull back the positive terminal cover 

8 

and disconnect the positive cable from

the battery.

Detach rubber band 

8 

at the bottom.

-

Lift the battery up and out.

Main work 

-

Insert battery into the battery compartment with the terminals facing to the front.

I 

Battery (YTX5L-BS)  (

.-

p. 204)

-

Reconnect rubber band 

O.

•

Info

I 

Contact disk 

e 

must be mounted between screw 

e 

and cable

socket 

0 

with the claws facing down.

-

Position the positive cable and mount and tighten the screw.
Guideline

Screw,  battery terminal 

M5 

-

Slide positive terminal cover 

8 

over the positive terminal.

-

Position the negative cable and mount and tighten the screw.

Guideline

Screw,  battery terminal 

M5 

-

Slide negative terminal cover 

8 

over the negative terminal.

Finishing work 

-

Mount the seat. (

.-

p. 76)

2.5 Nm 

(1.84 lbf ft) 

2.5 Nm 

(1.84 lbf ft) 

Summary of Contents for FE 350 2014
























































































































































































































































































Reviews:

No comments