Husqvarna F2303V4 Owner'S Manual Download Page 73

Page: 73 / 168

SERVICE WORK ON THE CHASSIS 12

K00518-01

Main work

–

Wash the air filter thoroughly in special cleaning liquid and
allow it to dry properly.

Air filter cleaner (

p. 156)

Info

Only press the air filter to dry it, never wring it out.

–

Oil the dry air filter with a high-grade air filter oil.

Oil for foam air filter (

p. 156)

–

Clean the air filter box.

–

Check the intake flange for damage and looseness.

Finishing work

–

Install the air filter.

(

p. 70)

–

Install the air filter box cover. (

p. 69)

12.25

Removing the right side cover

Preparatory work

–

Remove the air filter box cover. (

p. 69)

–

Remove the seat. (

p. 67)

F02343-10

Main work

–

Detach side cover in area

, pull off sideways in area

and take off toward the rear.

Summary of Contents for F2303V4









































































































































































Search results

Summary of Contents for F2303V4

Reviews:

Related manuals for F2303V4

Brands by name

Popular brands

Husqvarna F2303V4, Owner'S Manual

Search results

Summary of Contents for F2303V4

Reviews:

Related manuals for F2303V4

Brands by name

Popular brands