Husqvarna F2303V4 Owner'S Manual Download Page 59

Page: 59 / 168

SERVICE WORK ON THE CHASSIS 12

12.6

Installing the fork protector

F03463-11

–

Position the fork protector on the left fork leg. Mount and
tighten screws

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

–

Position the brake line, wiring harness, and clamp. Mount and
tighten screws

–

Position the fork protector on the right fork leg. Mount and
tighten screws

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

12.7

Removing the fork legs

Preparatory work

–

Remove the headlight mask with the headlight. (

p. 114)

–

Raise the motorcycle with a lift stand. (

p. 55)

–

Remove the front wheel.

(

p. 101)

S04825-10

Main work

–

Remove screws

and take off the clamp.

–

Remove the cable tie.

–

Remove screws

and take off the brake caliper.

–

Allow the brake caliper and brake line to hang loosely to the
side.

S03576-11

–

Loosen screws

. Remove the left fork leg.

–

Loosen screws

. Remove the right fork leg.

Summary of Contents for F2303V4









































































































































































Search results

Summary of Contents for F2303V4

Reviews:

Related manuals for F2303V4

Brands by name

Popular brands

Husqvarna F2303V4, Owner'S Manual

Search results

Summary of Contents for F2303V4

Reviews:

Related manuals for F2303V4

Brands by name

Popular brands