manualshive.com logo in svg

Husqvarna F2303U4, Owner'S Manual

Share
Download
Husqvarna F2303U4 Owner'S Manual Download Page 89

SERVICE WORK ON THE CHASSIS 12

87

F02365-10

(FE US)

–

Check that screw

1

is firmly seated.

Guideline

Screw, fixed
grip

M4

5 Nm (3.7 lbf ft)

Loctite

®

243™

Diamond

A

must be positioned visibly as shown in

the figure.

12.42

Adjusting the basic position of the clutch lever

H03648-11

–

Adjust the basic position of the clutch lever to your hand size
by turning adjusting screw

1

.

Info

When the adjusting screw is turned clockwise, the
clutch lever moves closer to the handlebar.
When the adjusting screw is turned counterclockwise,
the clutch lever moves away from the handlebar.
The range of adjustment is limited.
Turn the adjusting screw by hand only, and do not
apply any force.
Do not make any adjustments while riding.

12.43

Checking/correcting the fluid level of hydraulic clutch

Warning

Skin irritation

 

Brake fluid causes skin irritation.

–

Keep brake fluid out of the reach of children.

–

Wear suitable protective clothing and safety glasses.

–

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

–

Consult a doctor immediately if brake fluid has been swallowed.

–

Rinse the affected area with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact
with the eyes.

–

If brake fluid spills on to your clothing, change the clothing.

Note

Environmental hazard

 

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance
with the applicable regulations.

Info

The fluid level rises with increasing wear of the clutch facing discs.
Never use DOT 5 brake fluid. It is silicone-based and purple in color. Oil seals and clutch lines are not
designed for DOT 5 brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint.
Only use clean brake fluid from a sealed container.

Summary of Contents for F2303U4










































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands