Husqvarna F2303S0 Page 110 Repair Manual Download

Page: 110 / 337

12 FUEL TANK, SEAT, TRIM

- Grease O-rings G) lightly.

I Multi-purpose grease (00062010051) (

p. 307)

•

Info

Make sure that no grease gets into the fuel connec

tion.

- Mount fuel connection

with gaskets but do not tighten

yet.

✓ The cut-out

is aligned to the nut

- Tighten nut

Guideline

Nut, fuel pump fas

tener

M12x1.75

- Tighten fuel connection

Guideline

Fuel connection on

fuel tank

M8x1 .25

15 Nm (11.1 lbf ft)

10 Nm (7.4 lbf ft)

- Attach side covers in area

and position.

- Mount and tighten screws

Finishing work

- Install the fuel tank. (

p. 102)

- Install the right side cover. (

p. 99)

- Mount the seat. (

p. 1 00)

- Install the air filter box cover. (

p. 95)

12.11

Changing the fuel filter

108

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.
- Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

- Switch off the engine for refueling.

- Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

- If any fuel is spilled, wipe it off immediately.

- Observe the specifications for refueling.

Summary of Contents for F2303S0


















































































































































































































































































































































Search results

Summary of Contents for F2303S0

Reviews:

Related manuals for F2303S0

Brands by name

Popular brands

Husqvarna F2303S0, Repair Manual

Search results

Summary of Contents for F2303S0

Reviews:

Related manuals for F2303S0

Brands by name

Popular brands