Husqvarna F2203V4 Owner'S Manual Download Page 55

Page: 55 / 166

TUNING THE CHASSIS 11

11.16

Adjusting the handlebar position

Warning

Danger of accidents

A repaired handlebar poses a safety risk.

If the handlebar is bent or straightened, the material becomes fatigued. The handlebar may break as a
result.

–

Change the handlebar if the handlebar is damaged or bent.

F02950-10

–

Remove screws

. Take off the handlebar clamps. Take off

the handlebar and lay it to one side.

Info

Cover the components to protect them against dam-
age.
Do not bend the cables and lines.

–

Remove screws

. Take off the handlebar supports.

–

Place the handlebar supports in the required position. Mount
and tighten screws

Guideline

Screw, handle-
bar holder

M10

40 Nm (29.5 lbf ft)

Loctite

243™

Info

Position the left and right handlebar holders evenly.

–

Position the handlebar.

Info

Make sure the cables and wiring are positioned cor-
rectly.

–

Position the handlebar clamps. Mount and tighten screws

evenly.
Guideline

Screw, handlebar
clamp

20 Nm (14.8 lbf ft)

Info

Make sure the gap width is even.

Summary of Contents for F2203V4







































































































































































Search results

Summary of Contents for F2203V4

Reviews:

Husqvarna F2203V4, Owner'S Manual, Page: 55 / 166

Search results

Summary of Contents for F2203V4

Reviews: