manualshive.com logo in svg

Husqvarna F2203V4, Owner'S Manual, Page: 103 / 166

Share
Download
Husqvarna F2203V4 Owner'S Manual Download Page 103

WHEELS, TIRES 14

101

14.2

Installing the front wheel

Warning

Danger of accidents

 

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

H00935-10

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:

–

Change front wheel bearing.

–

Clean and grease shaft seal rings

1

and contact

surfaces

A

of the spacers.

Long-life grease (

p. 154)

–

Insert the spacers.

S04841-11

–

Clean and grease the wheel spindle.

Long-life grease (

p. 154)

–

Position the front wheel and insert the wheel spindle.

The brake linings are correctly positioned.

–

Mount and tighten screw

2

.

Guideline

Screw, front wheel
spindle

M20x1.5

35 Nm (25.8 lbf ft)

–

Operate the hand brake lever several times until the brake
linings are seated correctly against the brake disc.

–

Remove the motorcycle from the lift stand. (

p. 54)

–

Operate the front brake and compress the fork a few times
firmly.

The fork legs straighten.

–

Tighten screws

3

.

Guideline

Screw, fork stub

M8

15 Nm (11.1 lbf ft)

14.3

Removing the rear wheel

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 54)

Summary of Contents for F2203V4







































































































































































Reviews:

No comments