Husqvarna F2203V4 Owner'S Manual Download Page 101

Page: 101 / 166

BRAKE SYSTEM 13

–

Remove the brake linings.

–

Clean the brake caliper and the brake caliper bracket.

–

Check that spring plate in the brake caliper and brake pad
sliding plate in the brake caliper bracket are fitted correctly.

S04472-01

–

Insert the new brake linings.

–

Mount pin

The spring plate engages in the groove on the pin.

Info

Always change the brake linings in pairs.

–

Mount cotter pins

–

Operate the foot brake lever repeatedly until the brake lin-
ings are in contact with the brake disc and there is a pressure
point.

F03485-10

–

Correct brake fluid level to marking

Brake fluid DOT 4 / DOT 5.1 (

p. 152)

–

Mount and tighten screw cap

with membrane

Info

Use water to immediately clean up any brake fluid that
has overflowed or spilled.

Summary of Contents for F2203V4







































































































































































Search results

Summary of Contents for F2203V4

Reviews:

Husqvarna F2203V4, Owner'S Manual, Page: 101 / 166

Search results

Summary of Contents for F2203V4

Reviews: