Husqvarna F2201V1 Owner'S Manual Download

Page: 146 / 158

23 SUBSTANCES

144

Brake fluid DOT 4 / DOT 5.1

Standard/classification

–

DOT

Guideline

–

Use only brake fluid that complies with the specified standard (see specifications on the container) and that
exhibits the corresponding properties.

Recommended supplier

Castrol

–

REACT PERFORMANCE DOT 4

MOTOREX

–

Brake Fluid DOT 5.1

Coolant

Guideline

–

Only use high-grade, silicate-free coolant with corrosion inhibitor additive for aluminum motors. Low grade
and unsuitable antifreeze causes corrosion, deposits and frothing.

–

Do not use pure water as only coolant is able to meet the requirements needed in terms of corrosion pro-
tection and lubrication properties.

–

Only use coolant that complies with the requirements stated (see specifications on the container) and that
has the relevant properties.

Antifreeze protection to at least

−

25 °C (

−

13 °F)

The mixture ratio must be adjusted to the necessary antifreeze protection. Use distilled water if the coolant
needs to be diluted.

The use of premixed coolant is recommended.

Observe the coolant manufacturer specifications for antifreeze protection, dilution and miscibility (compatibility)
with other coolants.

Recommended supplier

MOTOREX

–

COOLANT M3.0

Engine oil (SAE 10W/50)

Standard/classification

–

JASO T903 MA2 (

p. 148)

–

SAE (

p. 148) (SAE 10W/50)

Guideline

–

Use only engine oils that comply with the specified standards (see specifications on the container) and that
possess the corresponding properties.

Fully synthetic engine oil

Recommended supplier

MOTOREX

–

Cross Power 4T

Summary of Contents for F2201V1































































































































































Search results

Summary of Contents for F2201V1

Reviews:

Related manuals for F2201V1

Brands by name

Popular brands

Husqvarna F2201V1, Owner'S Manual

Search results

Summary of Contents for F2201V1

Reviews:

Related manuals for F2201V1

Brands by name

Popular brands