Husqvarna DMT 700 Operator'S Manual Download Page 27

Page: 27 / 48

English

– 27

MENU SYSTEM

Menu system explanation

E-track, adjustment left

Water safety system

Battery voltage

Current blade depth

Blade depth stop setting

Run time will be displayed at start. While running, the
engine load will be displayed in % where 100% is max.

Engine or blade speed

E-track, position

Engine temperature

10 Blade depth stop

11 Blade clutch

12 E-track, adjustment right

Setup Menu 1

Language

Distance unit. Switch between metric and imperial length
units.

Return button (previous menu)

Backlight. Switch between three different levels of
brightness and an auto setting. Auto is default.

Temperature unit. Switch between Celsius and
Fahrenheit.

Languages

Select the required display language.

Return button (previous menu)

Browse to previous language

Browse to next language

Select button

Setup Menu 2

System information

Gearbox and blade information

Return button (previous menu)

Fault codes

Service Timer Menu

Calibrate E-track. Present E track position becomes
center position.

System information

Software related information.

Return button (previous menu)

GPL license

Engine information.

- DMT 700 Software ID.

Gearbox and blade information

Shows the recommended rpm and gear for available blade
sizes.

The tables are different depending on whether the machine is
configured for 1-Speed or 3-Speed gearbox. Select your
product model.

Return button (previous menu)

Browse to previous

Browse to next

Select button

<1200 RPM

CURRENT:

STOP:

WORKING HOUR

100

120

Language

Metric

Celsius

Backlight

Auto

Setup Menu 1

Press

button to enter Setup

Menu 2

ENGLISH

Press

button to enter Setup

Menu 1

Setup Menu 2

Calibrate

E-track

Fault

Codes

Service

Timer
Menu

System

Information

Gearbox

and Blade

Information

GPL

License

HMI

Serial Number
Hardware Number
Software Number
Bootloader Number

Engine

Serial Number
Model Number

Engine Working Hours
Time Since Last Regeneration

: YYYYWWXXXXX
: 580844701-A0001
: 123456789-A0001
: 5815361XX-AXXXX

: NOT KNOWN
: NOT KNOWN

: 123.5
: 34: 17:36

DMT 700, 1-Speed US

DMT 700, 1-Speed EU

Summary of Contents for DMT 700

















































Search results

Summary of Contents for DMT 700

Reviews:

Related manuals for DMT 700

Brands by name

Popular brands

Husqvarna DMT 700, Operator'S Manual

Search results

Summary of Contents for DMT 700

Reviews:

Related manuals for DMT 700

Brands by name

Popular brands