Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 171

Page: 171 / 216

18 SERVICE WORK ON THE ENGINE

169

S01051-10

Main work

–

Check the engine oil level.

Info

After switching off the engine, wait one minute before checking the level.

The engine oil must be between marking



and marking



of the oil level viewer.

» If the engine oil level is below the



mark:

–

Add engine oil. (

p. 175)

» If the engine oil level is above the



mark:

–

Correct the engine oil level.

18.3

Changing the engine oil and oil filter, cleaning the oil screens

Warning

Danger of scalding

Engine and gear oil get very hot when the motorcycle is ridden.

–

Wear suitable protective clothing and safety gloves.

–

In the event of scalding, rinse the area affected immediately with lukewarm water.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the applicable regula-

tions.

Info

Drain the engine oil while the engine is at operating temperature.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands