manualshive.com logo in svg

Husqvarna 701 Enduro 2017, Owner'S Manual

The Husqvarna 701 Enduro 2017 is a versatile off-road motorcycle designed for adventure enthusiasts. With its powerful engine and advanced features, this bike offers an exhilarating riding experience. Ensure proper maintenance and maximize your journey by accessing the free Owner's Manual for the Husqvarna 701 Enduro 2017, available for download at manualshive.com.

Share
Download
background image

14 WHEELS, TIRES

132

H01144-10

–

Check the tire age.

Info

The tire date of manufacture is usually contained in the tire label and is indi-

cated by the last four digits of the

DOT

number. The first two digits indicate

the week of manufacture and the last two digits the year of manufacture.
Husqvarna Motorcycles recommends that the tires be changed after 5 years at

the latest, regardless of the actual state of wear.

» If the tires are more than 5 years old:

–

Change the tires.

14.7

Checking the tire air pressure

Info

Low tire air pressure leads to abnormal wear and overheating of the tire.
Correct tire air pressure ensures optimal riding comfort and maximum tire service life.

400695-01

–

Remove the protection cap.

–

Check the tire air pressure when the tires are cold.

Tire air pressure, offroad, single rider

Front

1.5 bar (22 psi)

Rear

1.5 bar (22 psi)

Tire air pressure, road, solo

Front

1.8 bar (26 psi)

Rear

1.8 bar (26 psi)

Tire air pressure with passenger / fully loaded

Summary of Contents for 701 Enduro 2017

























































































































































































































Reviews:

No comments

Related manuals for 701 Enduro 2017

Kabuto FR-1 Instruction Manual preview
FR-1
Brand: Kabuto Pages: 12
GAS GAS TXT PRO - PART LIST 2010 Parts List preview
TXT PRO - PART LIST 2010
Brand: GAS GAS Pages: 64
Dennis Kirk Scorpion Exo-T520 Tech Manual preview
Scorpion Exo-T520
Brand: Dennis Kirk Pages: 10
SHERCO 2015 450 SEF-R Workshop Manual preview
2015 450 SEF-R
Brand: SHERCO Pages: 76
KC N901 User Manual preview
N901
Brand: KC Pages: 32
URAL Motorcycles cT 2022 Owner'S Manual preview
cT 2022
Brand: URAL Motorcycles Pages: 104
Palm SHUCK 12130 Manual preview
SHUCK 12130
Brand: Palm Pages: 14
Sealey PWH699R Instructions preview
PWH699R
Brand: Sealey Pages: 4
Warn 70558 Installation Instructions Manual preview
70558
Brand: Warn Pages: 8
Malaguti MADISON 300 2018 User Manual preview
MADISON 300 2018
Brand: Malaguti Pages: 120
APRILIA ETX 125 Manual preview
ETX 125
Brand: APRILIA Pages: 80
Denali HMT.07.11000 Instruction Manual preview
HMT.07.11000
Brand: Denali Pages: 2
Benelli BN600 Owner'S Manual preview
BN600
Brand: Benelli Pages: 32
Benelli 125 Enduro Workshop Manual preview
125 Enduro
Brand: Benelli Pages: 77
Livall BH6X Series Quick Start Manual preview
BH6X Series
Brand: Livall Pages: 44
APRILIA RST MILLE FUTURA - PART 2 2000 Manual preview
RST MILLE FUTURA - PART 2 2000
Brand: APRILIA Pages: 50
Honda ELSINORE MR50 Owner'S Manual preview
ELSINORE MR50
Brand: Honda Pages: 66
Honda Elite SE50 Owner'S Manual preview
Elite SE50
Brand: Honda Pages: 78

Brands by name

Popular brands

Load more brands