Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 111

Page: 111 / 216

13 BRAKE SYSTEM

109

V00502-10

Main work

–

Move the brake fluid reservoir mounted on the handlebar to a horizontal position.

–

Remove screws



–

Remove cover



with membrane



–

Add brake fluid to level



Guideline

Level



(brake fluid level below reser-

voir rim)

5 mm (0.2 in)

Brake fluid DOT 4 (

p. 200)

–

Position the cover with the membrane. Mount and tighten the screws.

Info

Clean up overflowed or spilled brake fluid immediately with water.

13.6

Checking the front brake linings

Warning

Danger of accidents

Worn-out brake linings reduce the braking effect.

–

Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcycles workshop will be glad

to help.)

Warning

Danger of accidents

Damaged brake discs reduce the braking effect.

If the brake linings are not changed in time, the brake lining carriers grind against the brake disc. As a consequence, the brak-

ing effect is greatly reduced and the brake discs are destroyed.

–

Check the brake linings regularly.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands