Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 103

Page: 103 / 216

12 SERVICE WORK ON THE CHASSIS

101

V00501-10

–

Remove screws



–

Remove cover



with membrane



–

Check the fluid level.

Fluid level



below container rim

4 mm (0.16 in)

» If the fluid level does not meet specifications:

–

Correct the fluid level of the hydraulic clutch.

Brake fluid DOT 4 (

p. 200)

–

Position the cover with the membrane. Mount and tighten the screws.

Info

Clean up overflowed or spilled brake fluid immediately with water.

12.25

Removing the engine guard

S01036-10

–

Remove screws



on the left and right.

–

Pull the engine guard forward out of the holders and remove it.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands