• Do not lift the battery charger by the power
cord. To disconnect the battery charger
from a mains socket, pull out the plug. Do
not pull the power cord.
• Keep all cables and extension leads away
from water, oil and sharp edges. Make
sure that the cable is not caught between
doors, fences or similar.
• Do not use the battery charger near
flammable materials or materials that can
cause corrosion. Make sure that the
battery charger is not covered. Pull out
the plug to the battery charger if there is
smoke or fire.
• Only charge the battery indoors in a
location with good airflow and away
from sunlight. Do not charge the battery
outdoors. Do not charge the battery in wet
conditions.
• Only use the battery charger where the
temperature is between 5 °C (41 °F) and
40 °C (104 °F). Use the charger in an
environment which has a good airflow, dry
and free from dust.
• Do not put objects into the cooling slots of
the battery charger.
• Do not connect the battery charger
terminals to metal objects as this can short
circuit the battery charger.
• Use approved wall sockets that are not
damaged.
• Use only three-wire outdoor extension
cords that have three-prong grounding
plugs and grounding receptacles that
accept the appliance's plug.
Safety instructions for maintenance
WARNING:
Read the warning
instructions that follow before you
do maintenance on the product.
• Remove the battery before you do
maintenance, other checks or assemble
the product.
• The operator must only do the
maintenance and servicing shown in this
operator's manual. Turn to your servicing
dealer for maintenance and servicing of a
larger extension.
• Do not clean the battery or the battery
charger with water. Strong detergent can
cause damage to the plastic.
• If you do not do maintenance, it decreases
the life cycle of the product and increases
the risk of accidents.
• Special training is necessary for all
servicing and repair work, especially for
the safety devices on the product. If
not all checks in this operator's manual
are approved after you have done
maintenance, turn to your servicing dealer.
We guarantee that there are professional
repairs and servicing available for your
product.
• Only use original spare parts.
Assembly
To assemble the cutting head
CAUTION:
Make sure that the
drive shaft inside the shaft engages
with the cut-out in the cutting head.
B
A
1. Loosen the screw on the cutting head. (A)
2. Fit the cutting head on the shaft so that the
screw (A) is aligned with the hole in the
shaft as shown.
3. Finger tighten the screw (A). Make sure
that screw (A) fits into the hole in the shaft.
4. Tighten screw (A).
5. Tighten screw (B).
To assemble the bar and chain
1. Unscrew the bar nut and remove the
protective cover.
2. Fit the bar over the bar bolt. Place the bar
in its rearmost position. Place the chain
over the drive sprocket and in the groove
on the bar. Begin on the top side of the
bar.
1824 - 003 - 28.06.2022
13
Summary of Contents for 525DEPS
