manualshive.com logo in svg

Husqvarna 520iRX, Operator'S Manual, Page: 24 / 36

Share
Download
Husqvarna 520iRX Operator'S Manual Download Page 24

3. Make sure that the green charging light on the

battery charger comes on. That means that the

battery is connected correctly to the battery charger.

4. When all LEDs on the battery come on, the battery is

fully charged.

5. To disconnect the battery charger from the mains

socket, pull the plug. Do not pull the cable.

6. Remove the battery from the battery charger.

Note: Refer to the battery and battery charger manuals

for more information.

To connect the battery to the product

WARNING: Only use Husqvarna original

batteries with the product.

1. Make sure that the battery is fully charged.
2. Push the battery into the battery holder of the

product. The battery locks into position when you

hear a click.

CAUTION: If the battery does not move

easily into the battery holder, the battery

is not installed correctly. This can cause

damage to the product.

3. Make sure that the battery is installed correctly.

Battery information

Refer to the operator's manual of the battery for

information about how to use the battery.

To start the product

Note: The product identifies the cutting attachment

when the cutting attachment is changed, is started and

the throttle is pressed. The product stops and the LED

flashes until the throttle is released and moves back to

its initial position. The cutting attachment is at this time

identified and prepared for operation.

1. Press and hold the start button until the green LED is

lit.

2. Use the power trigger to control the speed.

To operate the product

Automatic shutdown function

The product has a shutdown function that stops the

product if the product is not used. The green LED for

start/stop indication goes off and the product stops after

120 seconds.

To start the SavE function

The product has a power saving function. The SavE

function gives the longest operation time from the

battery.
1. Push the SavE button to start the function. The

green LED comes on to show that the function is on.

2. Push the SavE button again to stop the SavE

function.

To change the operation direction of the

trimmer head

It is possible to change the operation direction of the

trimmer head. This can be done at full speed or at stop

position. In the factory, the trimmer head is set to turn

clockwise. The green LED is off when the trimmer head

turns clockwise.

24

757 - 001 - 24.10.2018

Summary of Contents for 520iRX





































Reviews:

No comments