manualshive.com logo in svg

Husqvarna 2016 FE 250, Owner'S Manual

Share
Download
Husqvarna 2016 FE 250 Owner'S Manual Download Page 19

6

CONTROLS

17

Warning

Danger of poisoning

 

Fuel is poisonous and a health hazard.

–

Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with

the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with

soap and water. If fuel is swallowed, contact a physician immediately. Change clothing that has been contaminated with

fuel. Store fuel properly in a suitable canister and keep away from children.

Warning

Environmental hazard

 

Improper handling of fuel is a danger to the environment.

–

Do not allow fuel to get into the ground water, the ground, or the sewage system.

H00170-10

(FE EU)

–

Press release button

, turn the filler cap counterclockwise, and lift it off.

S00909-10

(FE AU/US)

–

Press release button

, turn the filler cap counterclockwise, and lift it off.

6.16

Closing the filler cap

H00170-11

(FE EU)

–

Replace the filler cap and turn clockwise until release button

locks in

place.

Info

Run the fuel tank breather hose

without kinks.

S00909-11

(FE AU/US)

–

Replace the filler cap and turn clockwise until release button

locks in

place.

Info

Run the fuel tank breather hose

without kinks.

Summary of Contents for 2016 FE 250





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands