Husqvarna 2016 FE 250 Owner'S Manual Download Page 16

Page: 16 / 124

CONTROLS

6.1

Clutch lever

H00165-10

The clutch lever



is fitted on the left side of the handlebar.

The clutch is hydraulically operated and self-adjusting.

6.2

Hand brake lever

H00166-10

The hand brake lever



is fitted on the right side of the handlebar.

The hand brake lever is used to activate the front brake.

6.3

Throttle grip

H00167-10

The throttle grip



is fitted on the right side of the handlebar.

6.4

Kill switch (FE EU/AU)

H00168-10

Kill switch



is fitted on the left side of the handlebar.

Possible states

• Kill switch

in basic position

–

the ignition circuit is closed in this position and

the engine can be started.

• Kill switch

pressed

–

the ignition circuit is open in this position, the engine

goes out if it was running, or does not start if it was off.

6.5

Kill switch (FE US)

S00889-10

Kill switch



is fitted on the left side of the handlebar.

Possible states

• Kill switch

in basic position

–

the ignition circuit is closed in this position and

the engine can be started.

• Kill switch

pressed

–

the ignition circuit is open in this position, the engine

goes out if it was running, or does not start if it was off.

Summary of Contents for 2016 FE 250





























































































































Search results

Summary of Contents for 2016 FE 250

Reviews:

Related manuals for 2016 FE 250

Brands by name

Popular brands

Husqvarna 2016 FE 250, Owner'S Manual

Search results

Summary of Contents for 2016 FE 250

Reviews:

Related manuals for 2016 FE 250

Brands by name

Popular brands