background image

Inst339  Filtrite  Salt Chlorinator V09.20 

12 

 

Maintenance of your Chlorinator 

 
 
Maintenance Schedule:   Performing these checks and maintenance will identify parts that have worn and require 
repair/replacement before further serious damage is sustained.   A small amount of regular care and attention to your 
pool equipment will help ensure long life and trouble free performance.
  
 

 

To protect against extremes of temperature, your unit is vented to allow expensive electronics to cool.   
Ants and some insects are often attracted to the warmer, dry environment inside the enclosure.  We 
recommend that, with power turned off, you spray a surface insecticide on the surfaces surrounding the 
control to prevent ant and insect ingress.   Repeat every three months or as necessary. 

 

 

Timing 

Maintenance Check 

Service action (if required) 

Fortnightly 

Check cell for calcium build up 
 
 
Check water chemistry 
 
 
 
 
Check cable connections to cell 

Soak cell in mixture of Filtrite Salt Cell 
Cleaner. Use a soft brush only if required 
 
Balance pH in pool and adjust output of unit 
to ensure satisfactory production of 
chlorine. 
 
Adjust pins by separating if not held firmly in 
place. Ensure not water contact is occurring 
with pins 
 

Three Monthly 

Check cell connections for leaks 
 
Check for insects/ ants 

Isolate Pump, turn power off, clean and 
grease O rings or replace if necessary 
 

Spray a

 

surface insecticide on the surfaces 

around the unit to prevent ant and insect 
ingress.

 

Six Monthly 

Check chlorine level setting and pump operating 
hours 
 
 
Prevent insect ingress to controller 

Adjust timer and output depending on 
demand for current season. 
 
Turn controller off, use a insect spray and 
spray onto walls around controller. Do not 
spay directly into unit. 

 
 
 

Important note: Regular maintenance is important to ensure long life and trouble free performance of your pool equipment.   
If unable to perform the maintenance yourself, contact your local Clark Rubber store who will arrange a trained service 
technician to perform the maintenance for you. 

 

 

 
 
 
 
 
 
 
 
 
 
 
 

Record your Equipment details here for quick reference: 
 
 

Model No.: 

____________________________ 

 
 

Serial No.: 

____________________________ 

Summary of Contents for Filtrite CX Series

















Reviews: