manualshive.com logo in svg

Hughes DIRECWAY DW7000, User Manual, Page: 87 / 98

Share
Download
Hughes DIRECWAY DW7000 User Manual Download Page 87

Appendix C • Home networking

 

1035978-0001  Revision A

73

Appendix C

Home networking

A terminal connected to a properly aligned antenna assembly can 
provide satellite connectivity for multiple computers on a 
wireless or wired (Ethernet) LAN. After the terminal and network 
are installed, every computer on the network can surf the Internet 
through the satellite signal.

If you connect the terminal to a LAN, you must:

•

Install and configure an Ethernet hub (or a router if you have 
a static IP address) or wireless network base station.

•

Install and configure a NIC (also called an adapter) in each 
computer you want to connect to the network. The NICs must 
be set to auto-negotiate. Refer to the manufacturer’s 
installation instructions.

•

If using a wired network, connect the computers to the 
Ethernet hub with Ethernet cable.

Note:

Connect multiple home computers and laptops to a single 

DIRECWAY Internet connection at no additional cost. Home 
networking equipment is required but not included. For network 
setup, support and configuration, contact your network hardware 
manufacturer and/or operating system software developer (Hughes 
Network Systems, LLC (HNS) is not responsible for home 
network management or troubleshooting). Simultaneous use of 
high bandwidth applications by multiple users may result in 
degradation of speed. Actual speeds may vary. Speed and 
uninterrupted use of service are not guaranteed.

Summary of Contents for DIRECWAY DW7000



































































































Reviews:

No comments