manualshive.com logo in svg

Hughes DIRECWAY DW7000, User Manual, Page: 46 / 98

Share
Download
Hughes DIRECWAY DW7000 User Manual Download Page 46

Chapter 4 • Troubleshooting

 

32

1035978-0001  Revision A

Confirming Web 

Acceleration is operational

Web Acceleration is a proprietary protocol provided by 
DIRECWAY. It optimizes Web browsing performance.

1. At the System Control Center, click on the System Status 

indicator. The System Status page appears. See Figure 22. 

2. Check the message in the 

Web Acceleration Status

 row.

If the message says 

Operational

, Web Acceleration is 

enabled and the System Status indicator is green. Proceed to 
the next troubleshooting step.
If the message says 

Not Operational

, Web Acceleration is 

disabled and the System Status indicator is yellow. Perform 
the following steps:
a. Check that receiving and transmitting are working.  If they 

are not, troubleshoot them as previously described.

b. Wait two hours. If Web Acceleration has not returned to 

Operational, go to step b.

c. Power cycle the terminal by unplugging the power cord 

from the power source, waiting 10 seconds, and plugging it 
back in. Check the Web Acceleration status again. If it is 
still not operational, or operational but you still cannot surf 
the Internet, proceed to the next troubleshooting step.

d. If Web Acceleration is still not operational after power 

cycling, contact customer support for assistance.

Figure 22:  Confirming Web Acceleration is operational

Summary of Contents for DIRECWAY DW7000



































































































Reviews:

No comments