INSTALLATION INSTRUCTIONS - LIGHTSCAPER LED FLOOD SHEET 1 OF 2
SAVE THESE INSTRUCTIONS
93135085 Rev. A
WARNING! Fixtures must be grounded and installed in accordance with the National Electrical Code and all local codes. Failure to do so may increase
the
RISK OF PERSONAL INJURY, PROPERTY DAMAGE, FIRE AND DEATH. Install and use so fixture failures do not cause a hazard and use only in
environments for which the product is specifically marked.
WARNING! This product can expose you to chemicals including lead and lead compounds, which are known to the State of California to cause cancer
and birth defects or other reproductive harm. For more informtion, go to : www.P65Warnings.ca.gov
WARNING! Dangerous voltage exist within the unit and all precautions usually observed in handling high voltage equipment should be observed when
replacing light engine or otherwise servicing luminares. Disregarding this warning could result in electrical shock and possible injury to the individual
installing or servicing this equipment. Installation and servicing should be done by qualified personnel.
CAUTION! Follow ALL luminaire recommendations, product markings, instructions, restrictions and warnings regarding luminaire operation and burning
position. Luminaire label shows electrical and environmental requirements and restrictions.
NOTE! This luminare is designed for outdoor lighting applications with ambient temperatures not exceeding 40°C (104°F).
All electrical work must be done by a qualified electrician.
Turn off electric power to all affected circuits and allow to cool before installation or servicing.
A regularly scheduled maintenance program should be established to retain optimum light output and reduce heat retention. Dusting with a soft, clean,
dry cloth is normally sufficient for the optical system. Any accumulation of dust or dirt should be removed regularly.
Carefully read these instructions before installing product. If you do not understand these instructions, before starting any work, contact your Hubbell
Lighting distributor or [email protected] or (864) 678-1000
Give instructions to facility owner/manager for future reference.
READ THOROUGHLY BEFORE INSTALLATION
FIGURE 1
Hubbell Lighting • 701 Millennium Boulevard • Greenville, SC 29607 • Phone: 864-678-1000
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
© 2016 Hubbell Lighting, All Rights Reserved • For more information visit our website: www.hubbelloutdoor.com
MOUNTING AND AIMING THE LIGHTSCAPER FLOOD FIXTURE WITH
KNUCKLE MOUNT
Tools Required:
Electrical wiring tools
3/16 inch Hex Key
Turn off power to electrical connections.
Wiring must be performed by a qualified electrician.
Make electrical connections according to the local and National Electrical
Codes.
Remove fixture from packaging along with hardware bag.
There are three electrical leads coming out of this fixture: Black (Line Voltage),
White (Neutral), and Green (Ground). Feed the electrical leads (Item 2 Fig.1)
through the 1/2 NPS threaded mounting hole into an outdoor-rated junction box
(not shown and not provided).
Seal 1/2 NPS knuckle threads with sealing compound (not provided) and thread
the knuckle into the junction box. Face the fixture LEDs in the desired direction of
aim and secure the knuckle into position on the junction box (not provided) by
tightening the lock nut (Item 1 Fig.1).
Make wiring connection (Item 2 Fig.1) to the supply leads using wire nuts
provided in the hardware bag. Seal and close junction box (not provided).
•
•
•
•
2
3
1
4
The Lightscaper Flood has two switches located underneath the housing that allow the selection of two
preset lumen output settings (2000lm and 1000lm) and three different color temperatures (3000K,
4000K, and 5000K). In addition, there are two dimming leads provided (Item 4 Fig 1) that when
connected to an external dimmer, will allow greater flexibility of desired lumen output. It is not
necessary to connect the dimming leads to a dimmer for the product to function. The dimming leads are
capped off and can remain disconnected. If the user chooses to connect the product to a dimmer, it is
recommended to set the lumen output switch to 2000lm for greatest range of adjustability.