Huawei V300R001 Parts Replacement Download Page 163

Page: 163 / 228

Figure 5-80

Running/Alarm indicator on a power module

Step 10

Confirm the replacement.

Perform a post-replacement inspection.
After the parts replacement, return to the SmartKit page and click

Replaced

. Then

complete the check after the replacement as prompted.

Check system status.
On the

Parts Replacement

page, click

Inspection

to check the system status again. If

any inspection item fails, rectify the fault based on the suggestions in the inspection
report.

After the preceding procedure is complete, check services on the host for any storage-
related error.

----End

Follow-up Procedure

After the power module is replaced, label it to facilitate subsequent operations.

5.9 Replacing a BBU

This section describes how to replace a BBU.

5.9.1 Replacing a BBU (for Dorado5000 V3)

This section describes how to replace a BBU.

Impact on the System

Replacing a BBU affects data security.

During the replacement, if all other BBUs fail, the system is no longer BBU-protected.
To enhance data security, the system forcibly implements LUN write protection, and the
system performance is compromised.

Prerequisites

The spare part is ready.

Configuration data has been backed up.

OceanStor Dorado V3 Series
Parts Replacement

5 Replacing FRUs

Issue 05 (2019-01-30)

155

Summary of Contents for V300R001





































































































































































































































Search results

Summary of Contents for V300R001

Reviews:

Brands by name

Popular brands

Huawei V300R001, Parts Replacement

Search results

Summary of Contents for V300R001

Reviews:

Brands by name

Popular brands