manualshive.com logo in svg

Huawei V300R001, Parts Replacement

Share
Download
Huawei V300R001 Parts Replacement Download Page 108

3.

After the preceding procedure is complete, check services on the host for any storage-
related error.

----End

Follow-up Procedure

After the system subrack is replaced, label it to facilitate subsequent operations.

5.4 Replacing a Disk Module

This section describes how to replace a disk module, including the replacement of risky disks
(disks that are not yet completely faulty) and faulty disks.

Impact on the System

During the replacement of a disk module, if system reconstruction is complete, host services
are not affected; if system reconstruction is not complete, host services are slightly affected.

Prerequisites

l

The spare part of the disk module is ready.

l

Huawei-certified disk modules that match the product model are used as spare disk
modules. These modules are obtained by service engineers based on the part codes of
failed disk modules.

l

The disk module that you want to replace has been located.

NOTE

You can locate a component in either of the following ways:

l

Locating a component based on alarms in DeviceManager: On the 

Alarms and Events

 page of

DeviceManager, view the help information and locate the component to be replaced.

l

Locating a component based on the status of its alarm indicator: For details about the indicators on
different components, see indicator introduction in the 

Product Description

 specific to your product.

Precautions

l

When handling a disk module, hold only its edge to prevent it from damage.

l

Remove and insert a disk module with even force. Excessive force may damage the
appearance or connectors of the disk module.

l

To prevent disk module damage, wait at least one minute between removal and insertion
actions.

l

To prevent data loss, replace only a disk module whose Alarm/Location indicator is
steady red.

l

Complete the replacement within five minutes after removing the original disk module.
Otherwise, the system heat dissipation is compromised.

l

Use SmartKit to replace a risky disk (that is not completely faulty yet).

l

Ensure that the spare part is inserted in to the same slot as the replaced disk module.
Otherwise, the system may work abnormally.

OceanStor Dorado V3 Series
Parts Replacement

5 Replacing FRUs

Issue 05 (2019-01-30)

Copyright © Huawei Technologies Co., Ltd.

100

Summary of Contents for V300R001





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands